aboutsummaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2016-10-17[media] radio-bcm2048: don't ignore errorsmedia/v4.9-3Mauro Carvalho Chehab1-0/+2
Remove this warning: drivers/staging/media/bcm2048/radio-bcm2048.c: In function 'bcm2048_set_rds_no_lock': drivers/staging/media/bcm2048/radio-bcm2048.c:467:6: warning: variable 'err' set but not used [-Wunused-but-set-variable] int err; ^~~ By returning the error code. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] pctv452e: fix semicolon.cocci warningskbuild test robot1-1/+1
drivers/media/usb/dvb-usb/pctv452e.c:115:2-3: Unneeded semicolon Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] flexcop-usb: don't use stack for DMAMauro Carvalho Chehab2-37/+72
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. While here, remove a dead function calling usb_control_msg(). Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] stk-webcam: don't use stack for DMAMauro Carvalho Chehab1-5/+11
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] s2255drv: don't use stack for DMAMauro Carvalho Chehab1-2/+13
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] cpia2_usb: don't use stack for DMAMauro Carvalho Chehab1-4/+30
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] digitv: handle error code on RC queryMauro Carvalho Chehab1-4/+6
There's no sense on decoding and generating a RC key code if there was an error on the URB control message. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dw2102: return error if su3000_power_ctrl() failsMauro Carvalho Chehab1-1/+1
Instead of silently ignoring the error, return it. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] nova-t-usb2: handle error code on RC queryMauro Carvalho Chehab1-3/+6
There's no sense on decoding and generating a RC key code if there was an error on the URB control message. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] technisat-usb2: use DMA buffers for I2C transfersMauro Carvalho Chehab1-5/+11
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. On this driver, most of the transfers are OK, but the I2C one was using stack. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] pctv452e: don't call BUG_ON() on non-fatal errorMauro Carvalho Chehab1-3/+4
There are some conditions on this driver that are tested with BUG_ON() with are not serious enough to hang a machine. So, just return an error if this happens. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] pctv452e: don't do DMA on stackMauro Carvalho Chehab1-55/+74
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] nova-t-usb2: don't do DMA on stackMauro Carvalho Chehab1-5/+13
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] gp8psk: don't go past the buffer sizeMauro Carvalho Chehab1-0/+11
Add checks to avoid going out of the buffer. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] gp8psk: don't do DMA on stackMauro Carvalho Chehab1-2/+12
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dtv5100: don't do DMA on stackMauro Carvalho Chehab1-2/+8
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dtt200u: handle USB control message errorsMauro Carvalho Chehab1-8/+18
If something bad happens while an USB control message is transfered, return an error code. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dtt200u: don't do DMA on stackMauro Carvalho Chehab1-29/+75
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dtt200u-fe: handle errors on USB control messagesMauro Carvalho Chehab1-9/+31
If something goes wrong, return an error code, instead of assuming that everything went fine. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dtt200u-fe: don't do DMA on stackMauro Carvalho Chehab1-30/+65
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dtt200u-fe: don't keep waiting for lock at set_frontend()Mauro Carvalho Chehab1-9/+0
It is up to the frontend kthread to wait for lock. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] digitv: don't do DMA on stackMauro Carvalho Chehab2-10/+15
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dibusb: handle error code on RC queryMauro Carvalho Chehab1-2/+6
There's no sense on decoding and generating a RC key code if there was an error on the URB control message. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dibusb: don't do DMA on stackMauro Carvalho Chehab2-25/+85
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dib0700_core: don't use stack on I2C readsMauro Carvalho Chehab1-1/+26
Be sure that I2C reads won't use stack by passing a pointer to the state buffer, that we know it was allocated via kmalloc, instead of relying on the buffer allocated by an I2C client. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] dib0700: be sure that dib0700_ctrl_rd() users can do DMAMauro Carvalho Chehab2-13/+16
dib0700_ctrl_rd() takes a RX and a TX pointer. Be sure that both will point to a memory allocated via kmalloc(). Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] cxusb: don't do DMA on stackMauro Carvalho Chehab2-27/+41
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] cinergyT2-fe: don't do DMA on stackMauro Carvalho Chehab1-23/+33
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] cinergyT2-fe: cache stats at cinergyt2_fe_read_status()Mauro Carvalho Chehab1-41/+7
Instead of sending USB commands for every stats call, collect them once, when status is updated. As the frontend kthread will call it on every few seconds, the stats will still be collected. Besides reducing the amount of USB/I2C transfers, this also warrants that all stats will be collected at the same time, and makes easier to convert it to DVBv5 stats in the future. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] cinergyT2-core: handle error code on RC queryMauro Carvalho Chehab1-3/+5
There's no sense on decoding and generating a RC key code if there was an error on the URB control message. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] cinergyT2-core: don't do DMA on stackMauro Carvalho Chehab1-23/+61
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-14[media] af9005: don't do DMA on stackMauro Carvalho Chehab1-138/+181
The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
2016-10-05Merge tag 'v4.8' into patchworkmedia/v4.9-1Mauro Carvalho Chehab1573-9350/+17620
Linux 4.8 * tag 'v4.8': (1761 commits) Linux 4.8 ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7 MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems include/linux/property.h: fix typo/compile error ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock() mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page() MAINTAINERS: Switch to kernel.org email address for Javi Merino x86/entry/64: Fix context tracking state warning when load_gs_index fails x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID x86/vdso: Fix building on big endian host x86/boot: Fix another __read_cr4() case on 486 sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock sctp: change to check peer prsctp_capable when using prsctp polices sctp: remove prsctp_param from sctp_chunk sctp: move sent_count to the memory hole in sctp_chunk tg3: Avoid NULL pointer dereference in tg3_io_error_detected() x86/init: Fix cr4_init_shadow() on CR4-less machines MIPS: Fix detection of unsupported highmem with cache aliases MIPS: Malta: Fix IOCU disable switch read for MIPS64 MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS ...
2016-10-02Linux 4.8Linus Torvalds1-1/+1
2016-10-02Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-armLinus Torvalds3-5/+13
Pull ARM fixes from Russell King: "Three relatively small fixes for ARM: - Roger noticed that dma_max_pfn() was calculating the upper limit wrongly, by adding the PFN offset of memory twice. - A fix from Robin to correct parsing of MPIDR values when the address size is larger than one BE32 unit. - A fix from Srinivas to ensure that we do not rely on the boot loader (or previous Linux kernel) setting the translation table base register a certain way in the decompressor, which can lead to crashes" * 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm: ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7 ARM: 8617/1: dma: fix dma_max_pfn() ARM: 8616/1: dt: Respect property size when parsing CPUs
2016-10-02ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7Srinivas Ramana1-1/+1
If the bootloader uses the long descriptor format and jumps to kernel decompressor code, TTBCR may not be in a right state. Before enabling the MMU, it is required to clear the TTBCR.PD0 field to use TTBR0 for translation table walks. The commit dbece45894d3a ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but doesn't consider all the bits for the size of TTBCR.N. Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to indicate the use of TTBR0 and the correct base address width. Fixes: dbece45894d3 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores") Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Srinivas Ramana <sramana@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2016-10-02Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds5-19/+16
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Thomas Gleixner: "The last regression fixes for 4.8 final: - Two patches addressing the fallout of the CR4 optimizations which caused CR4-less machines to fail. - Fix the VDSO build on big endian machines - Take care of FPU initialization if no CPUID is available otherwise task struct size ends up being zero - Fix up context tracking in case load_gs_index fails" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/entry/64: Fix context tracking state warning when load_gs_index fails x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID x86/vdso: Fix building on big endian host x86/boot: Fix another __read_cr4() case on 486 x86/init: Fix cr4_init_shadow() on CR4-less machines
2016-10-02Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds12-55/+101
Pull MIPS fixes from Ralf Baechle: "Another round of fixes: - CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems - CPS: Avoid BUG() when offlining pre-r6 CPUs - DEC: Avoid gas warnings due to suspicious instruction scheduling by manually expanding assembler macros. - FTLB: Fix configuration by moving confiuguratoin after probing - FTLB: clear execution hazard after changing FTLB enable - Highmem: Fix detection of unsupported highmem with cache aliases - I6400: Don't touch FTLBP chicken bits - microMIPS: Fix BUILD_ROLLBACK_PROLOGUE - Malta: Fix IOCU disable switch read for MIPS64 - Octeon: Fix probing of devices attached to GPIO lines - uprobes: Misc small fixes" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems MIPS: Fix detection of unsupported highmem with cache aliases MIPS: Malta: Fix IOCU disable switch read for MIPS64 MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS MIPS: clear execution hazard after changing FTLB enable MIPS: Configure FTLB after probing TLB sizes from config4 MIPS: Stop setting I6400 FTLBP MIPS: DEC: Avoid la pseudo-instruction in delay slots MIPS: Octeon: mark GPIO controller node not populated after IRQ init. MIPS: uprobes: fix use of uninitialised variable MIPS: uprobes: remove incorrect set_orig_insn MIPS: fix uretprobe implementation MIPS: smp-cps: Avoid BUG() when offlining pre-r6 CPUs
2016-10-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparcLinus Torvalds8-29/+90
Pull sparc fixes from David Miller: 1) Fix section mismatches in some builds, from Paul Gortmaker. 2) Need to count huge zero page mappings when doing TSB sizing, from Mike Kravetz. 3) Fix handing of cpu_possible_mask when nr_cpus module option is specified, from Atish Patra. 4) Don't allocate irq stacks until nr_irqs has been processed, also from Atish Patra. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: sparc64: Fix non-SMP build. sparc64: Fix irq stack bootmem allocation. sparc64: Fix cpu_possible_mask if nr_cpus is set sparc64 mm: Fix more TSB sizing issues sparc64: fix section mismatch in find_numa_latencies_for_group
2016-10-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds26-127/+171
Pull networking fixes from David Miller: 1) Fix wrong TCP checksums on MTU probing when checksum offloading is disabled, from Douglas Caetano dos Santos. 2) Fix qdisc backlog updates in qfq and sfb schedulers, from Cong Wang. 3) Route lookup flow key protocol value is wrong in ip6gre_xmit_other(), fix from Lance Richardson. 4) Scheduling while atomic in multicast routing code of ipv4 and ipv6, fix from Nikolay Aleksandrov. 5) Fix packet alignment in fec driver, from Eric Nelson. 6) Fix perf regression in sctp due to struct layout and cache misses, from Xin Long. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock sctp: change to check peer prsctp_capable when using prsctp polices sctp: remove prsctp_param from sctp_chunk sctp: move sent_count to the memory hole in sctp_chunk tg3: Avoid NULL pointer dereference in tg3_io_error_detected() act_ife: Fix false encoding act_ife: Fix external mac header on encode VSOCK: Don't dec ack backlog twice for rejected connections Revert "net: ethernet: bcmgenet: use phydev from struct net_device" net: fec: align IP header in hardware net: fec: remove QUIRK_HAS_RACC from i.mx27 net: fec: remove QUIRK_HAS_RACC from i.mx25 ipmr, ip6mr: fix scheduling while atomic and a deadlock with ipmr_get_route ip6_gre: fix flowi6_proto value in ip6gre_xmit_other() tcp: fix a compile error in DBGUNDO() tcp: fix wrong checksum calculation on MTU probing sch_sfb: keep backlog updated with qlen sch_qfq: keep backlog updated with qlen can: dev: fix deadlock reported after bus-off
2016-10-02MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systemsPaul Burton1-0/+11
When discovering the number of VPEs per core, smp_num_siblings will be incorrect for kernels built without support for the MIPS MultiThreading (MT) ASE running on systems which implement said ASE. This leads to accesses to VPEs in secondary cores being performed incorrectly since mips_cm_vp_id calculates the wrong ID to write to the local "other" registers. Fix this by examining the number of VPEs in the core as reported by the CM. This patch presumes that the number of VPEs will be the same in each core of the system. As this path only applies to systems with CM version 2.5 or lower, and this property is true of all such known systems, this is likely to be fine but is described in a comment for good measure. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/14338/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2016-10-01Merge tag 'scsi-fixes' of ↵Linus Torvalds4-5/+4
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fix from James Bottomley: "One final fix before 4.8. There was a memory leak triggered by turning scsi mq off due to the fact that we assume on host release that the already running hosts weren't mq based because that's the state of the global flag (even though they were). Fix it by tracking this on a per host host basis" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: Avoid that toggling use_blk_mq triggers a memory leak
2016-09-30Merge branch 'for-linus' of ↵Linus Torvalds1-0/+6
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fix from Dmitry Torokhov: "One small change to make joydev (which is used by older games) to bind to devices that export Z axis but not X or Y (such as TRC rudder)" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: joydev - recognize devices with Z axis as joysticks
2016-09-30Merge branch 'akpm' (patches from Andrew)Linus Torvalds5-64/+74
Merge more fixes from Andrew Morton: "Three fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: include/linux/property.h: fix typo/compile error ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock() mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()
2016-09-30include/linux/property.h: fix typo/compile errorJohn Youn1-1/+1
This fixes commit d76eebfa175e ("include/linux/property.h: fix build issues with gcc-4.4.4"). With that commit we get the following compile error when using the PROPERTY_ENTRY_INTEGER_ARRAY macro. include/linux/property.h:201:39: error: `u32_data' undeclared (first use in this function) PROPERTY_ENTRY_INTEGER_ARRAY(_name_, u32, _val_) ^ include/linux/property.h:193:17: note: in definition of macro `PROPERTY_ENTRY_INTEGER_ARRAY' { .pointer = { _type_##_data = _val_ } }, \ ^ This needs a '.' to reference the union member. It seems this was just overlooked here since it is done correctly in similar constructs in other parts of the original commit. This fix is in preparation of upcoming commits that will use this macro. Fixes: commit d76eebfa175e ("include/linux/property.h: fix build issues with gcc-4.4.4") Link: http://lkml.kernel.org/r/2de3b929290d88a723ed829a3e3cbd02044714df.1475114627.git.johnyoun@synopsys.com Signed-off-by: John Youn <johnyoun@synopsys.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-09-30ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()Eric Ren1-0/+10
The testcase "mmaptruncate" of ocfs2-test deadlocks occasionally. In this testcase, we create a 2*CLUSTER_SIZE file and mmap() on it; there are 2 process repeatedly performing the following operations respectively: one is doing memset(mmaped_addr + 2*CLUSTER_SIZE - 1, 'a', 1), while the another is playing ftruncate(fd, 2*CLUSTER_SIZE) and then ftruncate(fd, CLUSTER_SIZE) again and again. This is the backtrace when the deadlock happens: __wait_on_bit_lock+0x50/0xa0 __lock_page+0xb7/0xc0 ocfs2_write_begin_nolock+0x163f/0x1790 [ocfs2] ocfs2_page_mkwrite+0x1c7/0x2a0 [ocfs2] do_page_mkwrite+0x66/0xc0 handle_mm_fault+0x685/0x1350 __do_page_fault+0x1d8/0x4d0 trace_do_page_fault+0x37/0xf0 do_async_page_fault+0x19/0x70 async_page_fault+0x28/0x30 In ocfs2_write_begin_nolock(), we first grab the pages and then allocate disk space for this write; ocfs2_try_to_free_truncate_log() will be called if -ENOSPC is returned; if we're lucky to get enough clusters, which is usually the case, we start over again. But in ocfs2_free_write_ctxt() the target page isn't unlocked, so we will deadlock when trying to grab the target page again. Also, -ENOMEM might be returned in ocfs2_grab_pages_for_write(). Another deadlock will happen in __do_page_mkwrite() if ocfs2_page_mkwrite() returns non-VM_FAULT_LOCKED, and along with a locked target page. These two errors fail on the same path, so fix them by unlocking the target page manually before ocfs2_free_write_ctxt(). Jan Kara helps me clear out the JBD2 part, and suggest the hint for root cause. Changes since v1: 1. Also put ENOMEM error case into consideration. Link: http://lkml.kernel.org/r/1474173902-32075-1-git-send-email-zren@suse.com Signed-off-by: Eric Ren <zren@suse.com> Reviewed-by: He Gang <ghe@suse.com> Acked-by: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-09-30mm: workingset: fix crash in shadow node shrinker caused by ↵Johannes Weiner3-63/+63
replace_page_cache_page() Antonio reports the following crash when using fuse under memory pressure: kernel BUG at /build/linux-a2WvEb/linux-4.4.0/mm/workingset.c:346! invalid opcode: 0000 [#1] SMP Modules linked in: all of them CPU: 2 PID: 63 Comm: kswapd0 Not tainted 4.4.0-36-generic #55-Ubuntu Hardware name: System manufacturer System Product Name/P8H67-M PRO, BIOS 3904 04/27/2013 task: ffff88040cae6040 ti: ffff880407488000 task.ti: ffff880407488000 RIP: shadow_lru_isolate+0x181/0x190 Call Trace: __list_lru_walk_one.isra.3+0x8f/0x130 list_lru_walk_one+0x23/0x30 scan_shadow_nodes+0x34/0x50 shrink_slab.part.40+0x1ed/0x3d0 shrink_zone+0x2ca/0x2e0 kswapd+0x51e/0x990 kthread+0xd8/0xf0 ret_from_fork+0x3f/0x70 which corresponds to the following sanity check in the shadow node tracking: BUG_ON(node->count & RADIX_TREE_COUNT_MASK); The workingset code tracks radix tree nodes that exclusively contain shadow entries of evicted pages in them, and this (somewhat obscure) line checks whether there are real pages left that would interfere with reclaim of the radix tree node under memory pressure. While discussing ways how fuse might sneak pages into the radix tree past the workingset code, Miklos pointed to replace_page_cache_page(), and indeed there is a problem there: it properly accounts for the old page being removed - __delete_from_page_cache() does that - but then does a raw raw radix_tree_insert(), not accounting for the replacement page. Eventually the page count bits in node->count underflow while leaving the node incorrectly linked to the shadow node LRU. To address this, make sure replace_page_cache_page() uses the tracked page insertion code, page_cache_tree_insert(). This fixes the page accounting and makes sure page-containing nodes are properly unlinked from the shadow node LRU again. Also, make the sanity checks a bit less obscure by using the helpers for checking the number of pages and shadows in a radix tree node. Fixes: 449dd6984d0e ("mm: keep page cache radix tree nodes in check") Link: http://lkml.kernel.org/r/20160919155822.29498-1-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Antonio SJ Musumeci <trapexit@spawn.link> Debugged-by: Miklos Szeredi <miklos@szeredi.hu> Cc: <stable@vger.kernel.org> [3.15+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-09-30MAINTAINERS: Switch to kernel.org email address for Javi MerinoJavi Merino2-1/+2
Change my email address to my kernel.org account instead of the ARM one. Signed-off-by: Javi Merino <javi.merino@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-09-30x86/entry/64: Fix context tracking state warning when load_gs_index failsWanpeng Li1-2/+2
This warning: WARNING: CPU: 0 PID: 3331 at arch/x86/entry/common.c:45 enter_from_user_mode+0x32/0x50 CPU: 0 PID: 3331 Comm: ldt_gdt_64 Not tainted 4.8.0-rc7+ #13 Call Trace: dump_stack+0x99/0xd0 __warn+0xd1/0xf0 warn_slowpath_null+0x1d/0x20 enter_from_user_mode+0x32/0x50 error_entry+0x6d/0xc0 ? general_protection+0x12/0x30 ? native_load_gs_index+0xd/0x20 ? do_set_thread_area+0x19c/0x1f0 SyS_set_thread_area+0x24/0x30 do_int80_syscall_32+0x7c/0x220 entry_INT80_compat+0x38/0x50 ... can be reproduced by running the GS testcase of the ldt_gdt test unit in the x86 selftests. do_int80_syscall_32() will call enter_form_user_mode() to convert context tracking state from user state to kernel state. The load_gs_index() call can fail with user gsbase, gsbase will be fixed up and proceed if this happen. However, enter_from_user_mode() will be called again in the fixed up path though it is context tracking kernel state currently. This patch fixes it by just fixing up gsbase and telling lockdep that IRQs are off once load_gs_index() failed with user gsbase. Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1475197266-3440-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
2016-09-30x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUIDAndy Lutomirski1-12/+11
Otherwise arch_task_struct_size == 0 and we die. While we're at it, set X86_FEATURE_ALWAYS, too. Reported-by: David Saggiorato <david@saggiorato.net> Tested-by: David Saggiorato <david@saggiorato.net> Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave@sr71.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: aaeb5c01c5b ("x86/fpu, sched: Introduce CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT and use it on x86") Link: http://lkml.kernel.org/r/8de723afbf0811071185039f9088733188b606c9.1475103911.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>

Privacy Policy