aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/gpio
diff options
context:
space:
mode:
authorMarkus Mayer <mmayer@broadcom.com>2013-09-10 11:07:01 -0700
committerLinus Walleij <linus.walleij@linaro.org>2013-09-20 20:26:13 +0200
commit757651e3d60e5bff705743a301d64035b919fd03 (patch)
tree4c41388a881ed6c76fa64f22b4517026d5edd0ca /Documentation/devicetree/bindings/gpio
parentd8e0ac0824cd0868ea73f186d6511d710b068044 (diff)
gpio: bcm281xx: Add GPIO driver
Add the GPIO driver for the Broadcom bcm281xx family of mobile SoCs. These GPIO controllers may contain up to 8 banks where each bank includes 32 pins that can be driven high or low and act as an edge sensitive interrupt. Signed-off-by: Markus Mayer <markus.mayer@linaro.org> Reviewed-by: Christian Daudt <csd@broadcom.com> Reviewed-by: Tim Kryger <tim.kryger@linaro.org> Reviewed-by: Matt Porter <matt.porter@linaro.org> Reviewed-by: Stephen Warren <swarren@nvidia.com> [Added depends on OF_GPIO] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt52
1 files changed, 52 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt b/Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt
new file mode 100644
index 000000000000..4a63bc96b687
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-bcm-kona.txt
@@ -0,0 +1,52 @@
+Broadcom Kona Family GPIO
+=========================
+
+This GPIO driver is used in the following Broadcom SoCs:
+ BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
+
+The Broadcom GPIO Controller IP can be configured prior to synthesis to
+support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
+GPIO controller only supports edge, not level, triggering of interrupts.
+
+Required properties
+-------------------
+
+- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt outputs from the controller. There is one GPIO
+ interrupt per GPIO bank. The number of interrupts listed depends on the
+ number of GPIO banks on the SoC. The interrupts must be ordered by bank,
+ starting with bank 0. There is always a 1:1 mapping between banks and
+ IRQs.
+- #gpio-cells: Should be <2>. The first cell is the pin number, the second
+ cell is used to specify optional parameters:
+ - bit 0 specifies polarity (0 for normal, 1 for inverted)
+ See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
+- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The
+ second cell is used to specify flags. The following subset of flags is
+ supported:
+ - trigger type (bits[1:0]):
+ 1 = low-to-high edge triggered.
+ 2 = high-to-low edge triggered.
+ 3 = low-to-high or high-to-low edge triggered
+ Valid values are 1, 2, 3
+ See also .../devicetree/bindings/interrupt-controller/interrupts.txt.
+- gpio-controller: Marks the device node as a GPIO controller.
+- interrupt-controller: Marks the device node as an interrupt controller.
+
+Example:
+ gpio: gpio@35003000 {
+ compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
+ reg = <0x35003000 0x800>;
+ interrupts =
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };

Privacy Policy