|author||Jean Delvare <firstname.lastname@example.org>||2009-12-06 18:30:44 -0800|
|committer||Linus Torvalds <email@example.com>||2009-12-09 18:59:52 -0800|
Doc: use misc-devices/ dir for drivers
We have a directory for misc drivers documentation, let's use it. Signed-off-by: Jean Delvare <firstname.lastname@example.org> Signed-off-by: Randy Dunlap <email@example.com> Cc: "Darrick J. Wong" <firstname.lastname@example.org> Cc: Rodolfo Giometti <email@example.com> Signed-off-by: Linus Torvalds <firstname.lastname@example.org>
Diffstat (limited to 'Documentation/misc-devices')
2 files changed, 121 insertions, 0 deletions
diff --git a/Documentation/misc-devices/c2port.txt b/Documentation/misc-devices/c2port.txt
new file mode 100644
@@ -0,0 +1,90 @@
+ C2 port support
+(C) Copyright 2007 Rodolfo Giometti <email@example.com>
+This program is free software; you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation; either version 2 of the License, or
+(at your option) any later version.
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+This driver implements the support for Linux of Silicon Labs (Silabs)
+C2 Interface used for in-system programming of micro controllers.
+By using this driver you can reprogram the in-system flash without EC2
+or EC3 debug adapter. This solution is also useful in those systems
+where the micro controller is connected via special GPIOs pins.
+The C2 Interface main references are at (http://www.silabs.com)
+Silicon Laboratories site], see:
+- AN127: FLASH Programming via the C2 Interface at
+- C2 Specification at
+however it implements a two wire serial communication protocol (bit
+banging) designed to enable in-system programming, debugging, and
+boundary-scan testing on low pin-count Silicon Labs devices. Currently
+this code supports only flash programming but extensions are easy to
+Using the driver
+Once the driver is loaded you can use sysfs support to get C2port's
+info or read/write in-system flash.
+# ls /sys/class/c2port/c2port0/
+access flash_block_size flash_erase rev_id
+dev_id flash_blocks_num flash_size subsystem/
+flash_access flash_data reset uevent
+Initially the C2port access is disabled since you hardware may have
+such lines multiplexed with other devices so, to get access to the
+C2port, you need the command:
+# echo 1 > /sys/class/c2port/c2port0/access
+after that you should read the device ID and revision ID of the
+connected micro controller:
+# cat /sys/class/c2port/c2port0/dev_id
+# cat /sys/class/c2port/c2port0/rev_id
+However, for security reasons, the in-system flash access in not
+enabled yet, to do so you need the command:
+# echo 1 > /sys/class/c2port/c2port0/flash_access
+After that you can read the whole flash:
+# cat /sys/class/c2port/c2port0/flash_data > image
+# echo 1 > /sys/class/c2port/c2port0/flash_erase
+and write it:
+# cat image > /sys/class/c2port/c2port0/flash_data
+after writing you have to reset the device to execute the new code:
+# echo 1 > /sys/class/c2port/c2port0/reset
diff --git a/Documentation/misc-devices/ics932s401 b/Documentation/misc-devices/ics932s401
new file mode 100644
@@ -0,0 +1,31 @@
+Kernel driver ics932s401
+ * IDT ICS932S401
+ Prefix: 'ics932s401'
+ Addresses scanned: I2C 0x69
+ Datasheet: Publically available at the IDT website
+Author: Darrick J. Wong
+This driver implements support for the IDT ICS932S401 chip family.
+This chip has 4 clock outputs--a base clock for the CPU (which is likely
+multiplied to get the real CPU clock), a system clock, a PCI clock, a USB
+clock, and a reference clock. The driver reports selected and actual
+frequency. If spread spectrum mode is enabled, the driver also reports by what
+percent the clock signal is being spread, which should be between 0 and -0.5%.
+All frequencies are reported in KHz.
+The ICS932S401 monitors all inputs continuously. The driver will not read
+the registers more often than once every other second.
+The clocks could be reprogrammed to increase system speed. I will not help you
+do this, as you risk damaging your system!